ICL8038 jelgenerátor modul KIT-nincs forrasztva - Jelenlegi ára: 1 999 Ft

            
 
most csak nálam ennyi: 1. 999-HUF !!!
 "ICL8038 Function Signal Generator Module Sine Square Triangle Wave Output Kits"
 
Leírás:
ICL8038 pin functions:
1 foot, 12 foot: sine waveform adjusting terminal;
2 foot: sine wave output;
3 foot: triangle wave output;
4 foot, 5 foot: the frequency and duty cycle (or waveform asymmetry) adjustment;
6 foot: V +, the positive power supply;
7 foot: offset; 8 foot: frequency adjustment input terminal;
9 foot: square wave output.
This is an open collector output terminal, work should take a load resistor to the corresponding positive power supply terminal
from the pin, to get a TTL-compatible square-wave output, the load resistance must be connected to + 5V power supply;
10 foot: timing capacitor terminal;
11 foot: V-, negative power supply terminal or the ground. Use positive and negative power supply, 11 feet to the negative
supply, the output waveform are symmetrical with respect to 0V; use a single positive power supply, 11 feet grounded, the
output waveform is unipolar, uniform voltage is + VCC / 2;
13 feet, 14 Feet: Empty foot.
The kits are designed for a frequency range is 50-5KHz, two bands with a switch S to switch, RP1 is the frequency adjustment,
RP2 is the duty cycle adjustment, RP3 is a sine wave distortion adjustment. Circuit uses 12V single power supply, input from
the X1; X2, X3 is a waveform output side, you can use oscilloscope to observe three output waveforms.
ICL8038 pin functions:
1 foot, 12 foot: sine waveform adjusting terminal;
2 foot: sine wave output;
3 foot: triangle wave output;
4 foot, 5 foot: the frequency and duty cycle (or waveform asymmetry) adjustment;
6 foot: V +, the positive power supply;
7 foot: offset; 8 foot: frequency adjustment input terminal;
9 foot: square wave output.
This is an open collector output terminal, work should take a load resistor to the corresponding positive power supply terminal
from the pin, to get a TTL-compatible square-wave output, the load resistance must be connected to + 5V power supply;
10 foot: timing capacitor terminal;
11 foot: V-, negative power supply terminal or the ground. Use positive and negative power supply, 11 feet to the negative
supply, the output waveform are symmetrical with respect to 0V; use a single positive power supply, 11 feet grounded, the
output waveform is unipolar, uniform voltage is + VCC / 2;
13 feet, 14 Feet: Empty foot.
The kits are designed for a frequency range is 50-5KHz, two bands with a switch S to switch, RP1 is the frequency adjustment,
RP2 is the duty cycle adjustment, RP3 is a sine wave distortion adjustment. Circuit uses 12V single power supply, input from
the X1; X2, X3 is a waveform output side, you can use oscilloscope to observe three output waveforms.
EGY KIS SEGÍTSÉG A KÜTYÜHÖZ! Katt...
 A LÁTOGATÁSOD, SZERETETTEL VÁRLAK MÁSKOR ÉS MÁS TERMÉKEMNÉL IS!
                                                                                   
  
Kérem kattintson a felhasználónevem mellett i+ gombra, vagy az alábbi linkre:
Bemutatkozás, szállítási feltételek:
               A rendeléssel egyidejűleg kijelenti, hogy az ott leírtakat elolvasta és elfogadja!


Jelenlegi ára: 1 999 Ft
Az aukció vége: 2020-12-27 18:52 .